Uprog Gang 4x is production ic programmer, designed to support wide variety of programming devices. Thanks to USB 2.0 interface and specjalized internal FPGA designed microprocessor, we achived short programming times close to vendors maximum ratings. Its one of fastest IC programmers on worlds market.
The programmer consists of four independent programming modules, each of them provides 48 fully universal pin-drivers, providing a possibility of use different package adapters within one programmer. Wide range of supply and programming voltages ensures that future low-voltage devices will be supported. Full independence of programming modules additionaly increases efficiency of programmer speed for each module. It shows independently the status of other programming modules (concurent, asynchronous programming). Each module provides in-circuit programming connector.
User friednly Windows PC software gives intuitive operation. It supports many programmers simultaneously, so several programmers may be connected to the PC in order to increase efficiency of whole system.
Read time, Verify time
* - Verify during Programming
Uprog2 software allows to create a project that contains several different data sets for each of programmed device. It allows to freely manage programmable hardware. To the data set can be attached description that can describe various important things, like for example hardware version. Required data set can be selected by user during programming. This option is also useful for example to compare data, when reading the contents of various already programmed devices.
Uprog Gang x4 has Build-in interface for in-circuit programming, so as to be able to program chips working via SPI, I2C, BDM, JTAG, 1 WIRE, 3 WIRE and others. Serial programming interface was designed to allow to archive maximum data speed transfer and allows to adjust signal voltage level for any technology.
Serial Programming Adapter assure:
ICP allows to be pin-checked, so as to be able to keep good contacts with programmed chip.
New unique feature of Uprog programmers - Adapter Creator - allows to use many adapters from different providers. User is able to scan structure of the adapter, save it to file and use with selected device. Uprog programmers support Flash memories (typical and NAND), EPROMs, EEPROMs, serial EEPROMs, microcontrollers, PLDs/CPLDs. The device list is quickly developing and all software updates are free of charge!. If we obtain IC samples, we offer free update on customer's demand.
Uprog programmers always check if all pins have good contact to the socket before start of programming. It saves you against damages of programmed devices. You can always see very easy if you inserted the chip incorrectly. Pin which have poor contact are showed with red labels.
Features of 8-bit EPROM simulator:
Features of EPROM simulator:
Features of SPI simulator:
Ulogic, the Uprog based logic analyzer, makes the programmer an excelent measurement tool. Simply connect small adapter board directly to the programmers socket, run software and enjoy capturing the data.
1. The sampling rate is achieved in a limited buffer (12K samples near cursor T) with turned on option "Booster".
2. Available after memory expansion.
200MHz (1), 100MHz, 50MHz, 40MHz1, 20MHz, 10MHz, 5MHz, 4MHz1, 2MHz,1MHz, 500kHz, 400kHz1, 200kHz, 100kHz, 50kHz, 40kHz1, 20kHz, 10kHz, 5kHz, 4kHz1, 2kHz, 1kHz, 500Hz, 400Hz1, 200Hz
16 channels, maximum input voltage: ą50V
Adjustable size: 16384, 32768, 65536, 131072 (2), 262144 (2) samples
Edge - rising or falling edge, Edge, skip N - edge counter, Pattern - specified pattern, Edge and (or) Pattern - combinations of edge and pattern, Force - trigger can be also forced by the user
Treshold level for digital signals
Supported standards: 5V (TTL), 3.3V, 2.5V, 1.8V
A capture delay is the delay between trigger occurrence and data aquisition
Pre/Post Trigger buffer
Define how much of the sampling-buffer will be used to store data before the trigger
External clock input
External clock source may be used for sampling. Max. clock frequency 50MHz
The easy to use and flexible software displays captured data. Any number of channels can be displayed, the name of any channel can be changed. Three cursors are available for time/frequency measurements. Zoom options, jump to cursor buttons and scrollbar in connection with cursors make data analysing very easy
(1) Sampling rate available in limited buffer area (12K samples near cursor T) when Booster is enabled.
(2) Available after memory expansion.
Pattern generator is a tool designed for developing and testing of digital equipment. Thanks to user friendly pattern editor user can define any sequence of 16 digital signals and apply them to device's digital intetrface. Generated patterns are fully compliant with general standards of digital signals. Exept possibility of pattern definition user can change voltage level of output signals.
Changed algorithms of Flash units...
Improved algorithms of Dallas DS1230Y, DS1644, DS1225AD...
The improved automatic programming function in the Gang Mode option...
The improved automatic programming function...
The ST7FLIT19BF1 programming algorithm has been improved...
ul. Chełmońskiego 30
05-825 Grodzisk Mazowiecki
tel. +48 22 724 30 39, +48 22 755 69 83
fax +48 22 724 30 37