IC Programmers
Oscilloscopes, logic analyzers
Rotor balancing
Rotor balancing
image carousel

IC programmers Uprog portable

Uprog portable is the series of universal and extreme fast device ic portable programmers with ability to work without PC connection. Addtionally programmer can work with PC using USB 2.0 interface. Thanks internal specjalized microprocessor we achived short programming times close to vendor’s maximum ratings. Its one of fastest IC programmers on world’s market.
Uprog portable is able to working in High Speed and Full Speed mode. Thanks to usage Compact Flash card programmer can work in stand alone mode without posibillity of using PC computer. Uprog portable support all sizes of Compact Flash cards to allow big data files to be supported, what is especially important when big NAND flash memories has to be programmed.
Operation Windows software was designed for intuitive operation. It allows simultaneous multi-programmers support, so several programmers may be connected to the PC in order to increase efficiency of whole system.



Key features

  • Two operation modes: stand-alone and standard PC-hosted
  • USB interface - USB 2.0 (HighSpeed and FullSpeed) and USB 1.1 compatible
  • LCD display and keyboard
  • Specialized FPGA based microprocessor (20 ns cycle)
  • One of fastest programmers on the world’s market, programming times close to vendor’s maximum ratings
  • In-circuit programming connector (ICP)
  • 48-pins universal independent pindrivers which can provide VPP: 0-30V, VCC: 0.8 - 8V, CLK: ~360Hz-24MHz, GND
  • No adapter required for any DIL devices
  • Compact Flash card as data depository
  • Devices supported: EPROM, EEPROM, Flash, SPLD, CPLD, microcontrollers
  • Adapter Creator feature allows to use many adapters from different providers
  • Pin contact check feature
  • 8-bit EPROM/Flash simulator (option)
  • 16-bit EPROM/Flash simulator (option)
  • SPI memory simulator (option)
  • Ulogic - Uprog based logic analyzer with pattern generator feature (option)
  • Multi color status LEDs: power, busy, error, good
  • Banana jack on the case for grounding purpose and ESD protection
  • Software for Windows 2000/XP/Vista/Win7/Win8 (Win 32-bits and 64-bits) supports many independent programmers simultaneously



Sample programming times

Device

Memory size

Programming time

Read time, Verify time

K9F1G08U0A

1Gbit

95s

85s

M29W800DB

8Mbit

11s (P+V)*

2s

AM29F040B

4Mbit

12s (P+V)*

2s

AT25F4096

4Mbit

16s

2s

29DL64DF

64Mbit

58s (P+V)*

8,5s


* - Verify during Programming

In stand-alone mode programming time may be longer


Data versioning system

Uprog2 software allows to create a project that contains several different data sets for each of programmed device. It allows to freely manage programmable hardware. To the data set can be attached description that can describe various important things, like for example hardware version. After creating a project, data set can be stored on a CompactFlash card. Required data set can be selected by user during programming. This option is also useful for example to compare data, when reading the contents of various already programmed devices.



In-circuit programming, ICP

Uprog portable has Build-in interface for in-circuit programming, so as to be able to program chips working via SPI, I2C, BDM, JTAG, 1 WIRE, 3 WIRE and others.

programmers, measurement tools, vibration analysis

View od connectors for in-circuit programming

Serial programming interface was designed to allow to archive maximum data speed transfer and allows to adjust signal voltage level for any technology.
Serial Programming Adapter assure:

  • adaptation of voltage levels (1.2V - 5V)
  • fast data transfer
  • flexible connection between programmer and programmed device
  • posibility to connect VPP, VCC, GND, CLK, and 6 universal IO pins.


ICP allows to be pin-checked, so as to be able to keep good contacts with programmed chip.



Adapter Creator feature

New unique feature of Uprog programmers - Adapter Creator - allows to use many adapters from different providers. User is able to scan structure of the adapter, save it to file and use with selected device. Uprog programmers support Flash memories (typical and NAND), EPROMs, EEPROMs, serial EEPROMs, microcontrollers, PLDs/CPLDs. The device list is quickly developing and all software updates are free of charge!. If we obtain IC samples, we offer free update on customer demand.



Pin checking feature

Uprog programmers always check if all pins have good contact to the socket before start of programming. It saves you against damages of programmed devices. You can always see very easy if you inserted the chip incorrectly. Pin which have poor contact are showed with red labels.



8-bit EPROM simulator (option)

programmers, measurement tools, vibration analysis

Uprog portable as memory simulator

Features of 8-bit EPROM simulator:

  • memory sizes from 2KB to 64KB (optional to 256KB - after memory expansion)
  • short loading time
  • short access time: approx. 30ns
  • reset after data loading completion
  • variable voltage level: 1.8V - 5V



16-bit EPROM simulator (option)

Features of EPROM simulator:

  • memory size 64KWords (optional 128KWords and 256KWords - after memory expansion)
  • short loading time
  • short access time: approx. 30ns
  • reset after data loading completion
  • variable voltage level: 1.8V - 5V



SPI memory simulator (option)

Features of SPI simulator:

  • memory size 64KB
  • short loading time
  • short access time: approx. 30ns
  • reset after data loading completion
  • variable voltage level: 1.8V - 5V



Ulogic - digital signal analyser (option)

Main features:

  • 16 input channels
  • maximum sampling rate: 200MHz (1)
  • buffer length: 64K x 16 or 256K x 16 (2)
  • short data transfer time
  • external clock input
  • flexible trigger settings: edge, level (pattern) or combination of edge and/or pattern
  • Pre-trigger and Post-trigger buffer
  • capture delay and edge counter feature
  • input impedance: 470kΩ
  • sampling booster - the area near Trigger may be sampled with double rate
  • serial protocol interpreter: RS-232, SPI, I2C, 1-wire, CAN* (* - available soon)
  • state machine analyser
  • mnemonics code analyser for microprocessors
  • possibility of signal comparing (three independent buffers)
  • pattern genetrator

    programmers, measurement tools, vibration analysis

    Ulogic - Logic Analyzer based on Uprog portable



Ulogic, the Uprog based logic analyzer, makes the programmer an excelent measurement tool. Simply connect small adapter board directly to the programmers socket, run software and enjoy capturing the data.

Notes:
1. The sampling rate is achieved in a limited buffer (12K samples near cursor T) with turned on option "Booster".
2. Available after memory expansion.



Ulogic - technical parameters

Techical parameters

Specyfication

Sampling rates

200MHz (1), 100MHz, 50MHz, 40MHz1, 20MHz, 10MHz, 5MHz, 4MHz1, 2MHz,1MHz, 500kHz, 400kHz1, 200kHz, 100kHz, 50kHz, 40kHz1, 20kHz, 10kHz, 5kHz, 4kHz1, 2kHz, 1kHz, 500Hz, 400Hz1, 200Hz

Digital inputs

16 channels, maximum input voltage: ±50V

Buffer length

Adjustable size: 16384, 32768, 65536, 131072 (2), 262144 (2) samples

Trigger settings

Edge - rising or falling edge, Edge, skip N - edge counter, Pattern - specified pattern, Edge and (or) Pattern - combinations of edge and pattern, Force - trigger can be also forced by the user

Treshold level for digital signals

Supported standards: 5V (TTL), 3.3V, 2.5V, 1.8V

Capture Delay

A capture delay is the delay between trigger occurrence and data aquisition

Pre/Post Trigger buffer

Define how much of the sampling-buffer will be used to store data before the trigger

External clock input

External clock source may be used for sampling. Max. clock frequency 50MHz

Software

The easy to use and flexible software displays captured data. Any number of channels can be displayed, the name of any channel can be changed. Three cursors are available for time/frequency measurements. Zoom options, jump to cursor buttons and scrollbar in connection with cursors make data analysing very easy


Notes:
(1) Sampling rate available in limited buffer area (12K samples near cursor T) when Booster is enabled.
(2) Available after memory expansion.


Pattern Generator

Pattern generator is a tool designed for developing and testing of digital equipment. Thanks to user friendly pattern editor user can define any sequence of 16 digital signals and apply them to devices digital interface. Generated patterns are fully compliant with general standards of digital signals. Exept possibility of pattern definition user can change voltage level of output signals.

Main features:

  • 16 output channels
  • generation rates from 100MHz (state changes every 10ns) down to 200Hz
  • maximum buffer length: 64K samples (optionally 256K).
  • adjustable buffer length from 1 to maximal length
  • possibility of save defined signals for further use
  • available work modes:
    - Auto - generation of defined signals,
    - Repeat - cyclic generation of signals after trigger
    - Single - single generation of signals after trigger
  • adjustable voltage level of output: 1.8V, 2.5V, 3.3V, 5V (TTL).
  • user friendly pattern editor.



Our certificates
Certyfikat ISO 9001:2008 Certyfikat AQAP 2110:2009

News

Uprog programmer software update

11-10-2017

Software update...

Uprog programmer software update

08-08-2017

Software update...

Uprog programmer software update

01-07-2017

Software update...

Uprog programmer software update

10-04-2017

Software update...

Uprog programmer software update

05-03-2017

Update of software, improved algorithm of programing microcontroller AT29LV1024 and added microcontroller MT29F1G08ABADA...

RK-SYSTEM
ul. Chelmonskiego 30
05-825 Grodzisk Mazowiecki, Poland

tel. +48 22 724 30 39, +48 22 755 69 83
fax +48 22 724 30 37
E-mail: rk-system@rk-system.com.pl
Support: support@rk-system.com.pl

Privacy policy